Vienna 3.0 (Prepar3D V4)

martin[flytampa]
Site Admin
Posts: 4932

Re: Vienna 3.0 (Prepar3D V4 only)

Post by martin[flytampa] » Wed Mar 06, 2019 1:46 am

donkey20048 wrote:hi martin thanks the runway lights now appear when there is fog. However the actual lights on the airport do not turn on ie taxiways/ apron lights
yes, thats the normal behavior atm. only runway lights come on in fog. the spikes when looking at lights polys from a side angle are also "normal". That can be minimized with anisotropic filtering but not eliminated completely.
donkey20048
Posts: 19

Re: Vienna 3.0 (Prepar3D V4 only)

Post by donkey20048 » Wed Mar 06, 2019 3:41 am

awesome thanks for help martin
fpeter
Posts: 9

Re: Vienna 3.0 (Prepar3D V4 only)

Post by fpeter » Wed Mar 06, 2019 9:49 am

Hi Martin,
Could I get information that FT LOWW RWY 29 ILS: 292 or 293 or 294 degrees…?
I use P3D v4.4 ProSim737 2.15 is a SST simulator.
My FMC (OC) Approach REF in the attached image shows the data.
FMC.jpg
FMC Approach REF
FMC.jpg (526.91 KiB) Viewed 367 times
According to Navigraph 1903 FMS Data, it is 292 degrees
The Navigraph Charts also says 292 degrees
I got the information that this data is specified in a bgl file in the scenery addon…
The FT LOWW 2.9 Document Seek LOWW 29 RWY ILS OEX 294 degrees !?
I can't check what FT LOWW 3.0 is the data…
Could you help me get a clear picture of why the FMC shows 293 degrees…!?
Thank you for your advice or anyone ...
Best regards,
Peter
fpeter
Posts: 9

Re: Vienna 3.0 (Prepar3D V4)

Post by fpeter » Thu Mar 07, 2019 2:40 pm

Hi everyone,

I really want to understand where the OEX / 293 degree data comes from FMC Approach Ref… (?)

Regards,
Peter
P906
Posts: 21

Re: Vienna 3.0 (Prepar3D V4)

Post by P906 » Thu Mar 07, 2019 6:25 pm

on my FMC it shows 292° (Navigraph AIRAC 1903)
fpeter
Posts: 9

Re: Vienna 3.0 (Prepar3D V4)

Post by fpeter » Fri Mar 08, 2019 10:31 am

I also have the 1903 in the ProSim737 software.
Which simulator software do you use…?
And, software or hardware for FMC?
Regards,
Peter
fpeter
Posts: 9

Re: Vienna 3.0 (Prepar3D V4)

Post by fpeter » Fri Mar 08, 2019 1:33 pm

Hi,

I would be very happy to receive information on my question from FlyTampa…

Thank you very much!
Peter
P906
Posts: 21

Re: Vienna 3.0 (Prepar3D V4)

Post by P906 » Sat Mar 09, 2019 6:50 pm

i use ProSim 737

and the CPflight MCP/CDU`s hardware
martin[flytampa]
Site Admin
Posts: 4932

Re: Vienna 3.0 (Prepar3D V4)

Post by martin[flytampa] » Sun Mar 10, 2019 1:08 am

2016 chart shows 292 i believe.
http://www.flytampa.org/dwl/LOWW.pdf

Pretty sure the Addon FMC you use doesn't read that ILS data from the scenery, but from its own databse.
fpeter
Posts: 9

Re: Vienna 3.0 (Prepar3D V4)

Post by fpeter » Sun Mar 10, 2019 6:13 am

Hi everyone,
Today, I managed to solve my problem.
I've updated everything so far (FMS Ariac 1903, Herve Sors Navaids Update)…
Last night I noticed that the Herve Sors, World Navaids contained one bgl.
This is the magdec bgl!
There is also a magdec bgl in the ProSim737 Database folder (2015)
Overwritten by Herve Sors magdec bgl (2019)
With this, my problem is "293 degrees…" and the attached image shows that the correct 292 degrees is already shown on the FMC Approach REF page.
20190310_105835.jpg
Korrekt FMC Approach REF side, "292 degrees"
20190310_105835.jpg (1.46 MiB) Viewed 269 times
Thanks to everyone for your answer and advice…, and many thanks Herve Sors...!
Best regards,
Peter
Post Reply