SODE Jetways to Sydney Airport P3D v4

XCLTM3
Posts: 69

Re: SODE Jetways to Sydney Airport P3D v4

Post by XCLTM3 » Sun Mar 24, 2019 3:12 pm

shane2801 wrote:
Wed Mar 20, 2019 9:54 pm
HI
Thanks for the reply. I do have GSX version 2 installed and I re-downloaded fly Tampa Sydney. I would still like to use Flukey's jetways though
Hi Shane,

have you been able to resolve the issue yet?

Rgds,

Steve
shane2801
Posts: 15

Re: SODE Jetways to Sydney Airport P3D v4

Post by shane2801 » Tue Mar 26, 2019 4:18 am

Hi Stever
I reinstalled Fly Tampa Sydney. So I need to start from scratch. Im not too sharp when it comes to changing files so I probably did something wrong. Can you give any additional tips as to how you go about changing these files etc?
XCLTM3
Posts: 69

Re: SODE Jetways to Sydney Airport P3D v4

Post by XCLTM3 » Tue Mar 26, 2019 3:12 pm

shane2801 wrote:
Tue Mar 26, 2019 4:18 am
Hi Stever
I reinstalled Fly Tampa Sydney. So I need to start from scratch. Im not too sharp when it comes to changing files so I probably did something wrong. Can you give any additional tips as to how you go about changing these files etc?
Hi Shane,

I haven't as yet downloaded or used Flukeys files, so I'm not clear regarding the set of procedures/instructions. I carried out my own alterations to YSSY using GSX 2 - but these are not real world accurate changes, such as what Flukey states he has done.

If there is any part or parts of the installation you're not clear on - post the full set of instructions here and I'll take a look at them and try to guide you remotely from within the forum. It'll be a little more cumbersome this way, but we might still yield the results you're after.

Cheers,

Steve
shane2801
Posts: 15

Re: SODE Jetways to Sydney Airport P3D v4

Post by shane2801 » Tue Mar 26, 2019 10:08 pm

Hi Steev
Thanks for the help. I will try once more with Flukeys instructions. I will advise on how I go.
shane2801
Posts: 15

Re: SODE Jetways to Sydney Airport P3D v4

Post by shane2801 » Wed Mar 27, 2019 12:50 am

Hi guys
I have been successful in my endeavours. Thanks Steve for the help and Flukey for the files. Much appreciated
XCLTM3
Posts: 69

Re: SODE Jetways to Sydney Airport P3D v4

Post by XCLTM3 » Wed Mar 27, 2019 3:07 pm

shane2801 wrote:
Wed Mar 27, 2019 12:50 am
Hi guys
I have been successful in my endeavours. Thanks Steve for the help and Flukey for the files. Much appreciated
Hi Shane,

glad to hear you were able to sort it out - enjoy!

Steve
Flukey
Posts: 104

Re: SODE Jetways to Sydney Airport P3D v4

Post by Flukey » Fri Apr 26, 2019 8:12 pm

YSSY GSXv2 update to the one I posted on Page1, https://www.inibuilds.com/gsx-australia
Includes:

- Dual Aerobridges at Gate 58 as per RW.
- Amended wording on pushbacks for Intl 1 + 2 Aprons.
- Updated pushback for Gate6 intl which pushes acft onto the intl1 apron tail South.
- Added Pushback for gate 57 to allow tail east on TWY G
- General Cleanup on a couple of Pushbacks from various gates
Attachments
2019-4-27_10-40-58-127.jpg
2019-4-27_10-40-58-127.jpg (434.84 KiB) Viewed 3384 times
Last edited by Flukey on Fri May 17, 2019 10:31 pm, edited 1 time in total.
NZ255
Posts: 4

Re: SODE Jetways to Sydney Airport P3D v4

Post by NZ255 » Fri Apr 26, 2019 9:25 pm

Thank you :)

Edit: Don't forget to disable the Safedock via the FlyTampa control panel as Flukey has added GSX ones.
shane2801
Posts: 15

Re: SODE Jetways to Sydney Airport P3D v4

Post by shane2801 » Sun May 05, 2019 10:38 pm

Hi guys
So you just re-do it all again with this new file?
shane2801
Posts: 15

Re: SODE Jetways to Sydney Airport P3D v4

Post by shane2801 » Mon May 06, 2019 6:03 am

It all sorted. Thanks for the update Flukey
Flukey
Posts: 104

Re: SODE Jetways to Sydney Airport P3D v4

Post by Flukey » Sat Feb 15, 2020 4:36 am

Update to my YSSY GSXv2 file located - https://www.inibuilds.com/gsx-australia

Update - https://drive.google.com/file/d/16JWG0w ... sp=sharing

Changes/

Foxtrot Parking bays:

Updated the Bay Stop points to better match the Saab 340 acft type used by REX

Updated start position for bay F7 to match real world.

F4,5 & 6 Updated to allow GSX to work when using the A bays for Rex S340 acft type
Tip - No pushback required from the A bays, so do not use the pushback option

Domestic Gates:

44/44A, Added 3rd pushback option for acft to be pushed back on to TWYG Tail west.
ACFT type A330 parks in bay 44,
ACFT type B737 must be moved to Start point 44A. This will allow other AI or online acft to park into Bay 42

45/45A - Please ensure that when using this gate with acft B737 you slew into the A bay before using GSX this will prevent non-normal pushback when using the 737 option. This will also allow other AI or online acft to park into Bay 43 without conflict

Gate 11 - Amended pushback sequence

International Gates:

Gate 30 - Amended Pushback stop point to prevent acft being pushed into the terminal
Gate 51 - Amended Pushback stop point to prevent acft being pushed into the terminal

Gate 10,24 & 25, Pushback stop point located at Gate9

Gate 24 - Added pushback option for acft type B737/A320 which parks at this gate as well.

Cargo Bays:

Parking 1,2 & 3 - update pushback point for RWY ops 34L/R & 16L to start of A1 taxiway

Image

Image

Image
youngie63
Posts: 5

Re: SODE Jetways to Sydney Airport P3D v4

Post by youngie63 » Mon Apr 06, 2020 12:43 am

G’day mate, a quick question re the replacement bgl. Is there just the single bgl (from your zip file) to go into the YSSY/scenery folder?

Cheers youngie63
Goofie
Posts: 3

Re: SODE Jetways to Sydney Airport P3D v4

Post by Goofie » Wed Jul 01, 2020 8:58 pm

Hi Flukey

Can we use your gx.ini file in conjuction with Urmel's BGL file and VDGS.xml file?
Cheers
Damian
Post Reply