SYDNEY problems after Installing Australia V2

Post Reply
piano@bigpond.net.au
Posts: 2

SYDNEY problems after Installing Australia V2

Post by piano@bigpond.net.au » Mon Jun 17, 2019 12:10 am

just wondering out there, If anyone has installed the ORBX Australia V2.. Its altered the Tampa SYDNEY scenery adding different gates that don't move, double taxi lines and double runways

Is Fly Tampa or ORBX aware of this problem.
Can anyone shed some light
Kind regards
Michael
Flukey
Posts: 104

Re: SYDNEY problems after Installing Australia V2

Post by Flukey » Fri Jun 28, 2019 3:51 am

Go to your ORBX folder - Lockheed Martin\Prepar3D v4\ORBX\FTX_AU\FTXAUv2_05_SCENERY\scenery, find the YSSY files and turn to .off

That will fix your issue

On a side note being ORBX is landclass scenery make sure it is below all your 3rd party airports in the scenery library
BoazDK
Posts: 220

Re: SYDNEY problems after Installing Australia V2

Post by BoazDK » Sun Jul 28, 2019 3:37 pm

Flukey wrote:
Fri Jun 28, 2019 3:51 am
Go to your ORBX folder - Lockheed Martin\Prepar3D v4\ORBX\FTX_AU\FTXAUv2_05_SCENERY\scenery, find the YSSY files and turn to .off

That will fix your issue

On a side note being ORBX is landclass scenery make sure it is below all your 3rd party airports in the scenery library
Nope... I will now try again after removing the Sydney LC from Flytampa
BoazDK
Posts: 220

Re: SYDNEY problems after Installing Australia V2

Post by BoazDK » Mon Jul 29, 2019 3:54 am

deleting the Sydney LC scenery.cfg entry solved the crashes
TgfyosVevy
Posts: 1

SYDNEY problems after Installing Australia V2

Post by TgfyosVevy » Wed Sep 04, 2019 12:25 am

Okay Ill make sure to check that out, and if that does so happen to be the case, do I need endlinks for the rear as well if I get them lowered? Or does this only apply to the front wheels
remontlax
Posts: 2

SYDNEY problems after Installing Australia V2

Post by remontlax » Sun Sep 15, 2019 2:49 pm

There is no way to patch the fact that you cannot install from the CD. You will need to take this up with Enlight, as they are responsible for the production of the CDs.
RichardWSwan
Posts: 3

Re: SYDNEY problems after Installing Australia V2

Post by RichardWSwan » Wed Dec 02, 2020 12:13 am

Hi Fly Tampa Forum
ORBX adjustments always changes add on scenery.

I have done all the above to fix my problem with Fly Tampa YSSY changing ever time I alter ORBX Scenery, I have turned both the .bgl files OFF, Lorby has all my 3rd Party Add on's above FTX scenery, But to no avail. Every Time I make some adjustments in ORBX scenery, my Fly Tampa YSSY (and all my NZ add on's, USA add on's) change, and to fix them I have to reinstall all my 3rd Party Add On airports, I have 10 add on airports and this takes a lot of time. I have Prepar3DV5 and I use Lorby SI. My friend and myself have had this problem for several years now and ORBX's fix does not work. Also I have tried and unchecked all my 3rd Party Add-on airports , this did not fix the problem. Does any other Fly Tampa Simmer have this problem, or does anyone know how to fix it, it is driving me and my friend mad.

Regards
Richard
Post Reply