Falling through Q and clipping the wing on invisible objects

Daantjeplanes
Posts: 3

Falling through Q and clipping the wing on invisible objects

Post by Daantjeplanes » Wed Nov 18, 2020 8:55 am

Hi,

Since about a week I have a problem where I taxi on Q and my plane jumps back into the sky because it clipped with a invisible object on the side of the 2 bridges. Anyone with the same problem or a fix? I have allready reinstalled the scenery twice and its in P3D V5.1

Kind regards,
Daan
Soundman
Posts: 2

Re: Falling through Q and clipping the wing on invisible objects

Post by Soundman » Wed Nov 18, 2020 5:58 pm

Hi Daan,

The same problem happens here.
It started after the Prepar3d 5.1 upgrade.

The aircraft trips on all viaduct/tunnel/overpasses.
Some examples:
  • Coming from 18R towards W5 at the highway A5 overpass
  • Taxiway Q at highway A4 overpass
  • Taxiway A (near A21) at highway A4 tunnel
In all cases with PMDG NGXU or PMDG 747.
EHAMProblem
Posts: 3

Re: Falling through Q and clipping the wing on invisible objects

Post by EHAMProblem » Thu Nov 19, 2020 11:05 am

Yeah just reported the same, have 5.1 and my 747 has these problems too... Also on S2 at the Cargo Apron
jasperk
Posts: 1

Re: Falling through Q and clipping the wing on invisible objects

Post by jasperk » Tue Nov 24, 2020 4:15 pm

Hi,
Any solution to this problem yet? Since the upgrade to P3Dv5.1 HF1 I have the same problem on a couple of "bridge" points.

Thank you in advance
mclaren3465
Posts: 1

Re: Falling through Q and clipping the wing on invisible objects

Post by mclaren3465 » Sat Nov 28, 2020 5:26 pm

I am having the issue on taxiway V going to/from 36L as well as Q. My guess is some sort of default elevation data has changed in v5.1 that is causing a mismatch with the canals/roadways that the bridges go over.
aceridgey
Posts: 76

Re: Falling through Q and clipping the wing on invisible objects

Post by aceridgey » Mon Nov 30, 2020 1:55 pm

Came here to report the same issue, falling through the bridges near 18C and also on taxiway A to H.
emilios[flytampa]
Site Admin
Posts: 1369

Re: Falling through Q and clipping the wing on invisible objects

Post by emilios[flytampa] » Wed Dec 02, 2020 1:02 pm

Sorry for the delay guys, will have to check if the latest P3D version altered any stock data at the airport.
Alex48
Posts: 5

Re: Falling through Q and clipping the wing on invisible objects

Post by Alex48 » Mon Dec 14, 2020 4:57 am

aceridgey wrote:
Mon Nov 30, 2020 1:55 pm
Came here to report the same issue, falling through the bridges near 18C and also on taxiway A to H.
Same problem here when taxiing via taxiway Q at the overpass with the A4 highway. The aircraft is then violently thrown away. Sim is Prepar3D_v5_Academic_5.1.12.26829.
emilios[flytampa]
Site Admin
Posts: 1369

Re: Falling through Q and clipping the wing on invisible objects

Post by emilios[flytampa] » Tue Dec 15, 2020 6:21 pm

No changes that I can see here, at least stock aircraft can walk on the bridges normally. Has anyone tried with default aircraft? Any chance an alternative AFCAD is being used? (or has the ZHAM.bgl been moved from the scenery folder for any reason? )
Source41
Posts: 5

Re: Falling through Q and clipping the wing on invisible objects

Post by Source41 » Tue Dec 15, 2020 7:22 pm

emilios[flytampa] wrote:
Tue Dec 15, 2020 6:21 pm
No changes that I can see here, at least stock aircraft can walk on the bridges normally. Has anyone tried with default aircraft? Any chance an alternative AFCAD is being used? (or has the ZHAM.bgl been moved from the scenery folder for any reason? )
I tested with default F35 and didn't fall through at least on the Victor taxiway. I have fallen through on all taxiways with a bridge with the PMDG 747. I do have a file titled ZHAM_Flyatmpa.bgl The file itself does have that typo. Only added BGL in my case is the inibuilds EHAM_DL_V2.BGL but I have the issue with or without that one.
Carliolian
Posts: 4

Re: Falling through Q and clipping the wing on invisible objects

Post by Carliolian » Wed Dec 16, 2020 4:00 am

I have the same problem, it's getting very annoying. Any progress? I have also reinstalled no improvement.
emilios[flytampa]
Site Admin
Posts: 1369

Re: Falling through Q and clipping the wing on invisible objects

Post by emilios[flytampa] » Wed Dec 16, 2020 6:21 pm

There will be an updated installation within the next week with small fixes, including this one.
Source41
Posts: 5

Re: Falling through Q and clipping the wing on invisible objects

Post by Source41 » Wed Dec 16, 2020 6:34 pm

emilios[flytampa] wrote:
Wed Dec 16, 2020 6:21 pm
There will be an updated installation within the next week with small fixes, including this one.
You're the best! Thanks so much.
big_al
Posts: 101

Re: Falling through Q and clipping the wing on invisible objects

Post by big_al » Tue Dec 29, 2020 7:06 am

emilios[flytampa] wrote:
Wed Dec 16, 2020 6:21 pm
There will be an updated installation within the next week with small fixes, including this one.
I found this issue the hard way last night. Waiting on the fixes thanks :)
Post Reply